Electrical Control Design for real industrial applications

Description

Hello guys in Our Course you will learn All steps to Make a Full Electrical Control Design for any Project, in our Course we will discuss all Basic components in details after that we'll make a Full Electrical Control Design for about 15 applications

• This course is designed to teach students how to design an Electrical Control circuit to perform a specific desired function. Taking this course will give students a much better understanding for the most complicated Electrical control systems which they will face in the Industrial sector in the real life. so our course aims to teach students the fundamentals of Electrical Control design.  Starting from Basic Components ( Contactor - C.B - Relays - Timers - Elec switches - Fuses - Protection devices - Sensors - Encoders ), then we'll discuss the basic concepts for the Design like " latching - Interlocking - controlling from different places ..etc.", after that we'll make designing for many Electrical control circuits manually and using EKTS software for simulation.
  

• This course is structured in such a way that each section is dedicated to a specific topic in regards to Electrical Control Design. The lectures contained in each section describe in detail the different tools and techniques used to design Electrical Control circuits.

• There are assignments and Exercises throughout this course that students can use them to exam themselves, also we have a separated section for Lab, so you can get the most benefit from this course.
  
  Plan of Our Course will be like that :
  
  1- section (1) :  ( Introduction )
  
             - introduction for Electrical Control systems
             - basics of Electrical Power system
                   
  2- section (2) :  ( Basic Components for Electrical Control system )
  
              - Contactor and all types of Circuit Breakers ( MCB - MCCB - ACB ) in details 
              - How to calculate C.B rating and cable Sizing

              - Electric switches (Push buttons - Selector switch …etc.)  and Fuses in details
              - Electrical Relays (mechanical relay - SSR - Latch relay)
              - All Types of Faults in the Electrical control system
              - Protection Devices (Over-under Voltage relay & phase sequence-failure relay & Total protection device)
              - Overload relay in details

              - All types of Timers ( On-delay timer - 24 hours timer - Star/Delta timer - pneumatic timer )
  
  3- section (3) :  ( Lab for all Basic components )
  
  we'll see all these components in the practical life and the way of wiring for them
  
  4- section (4) :  ( Fast Revision for Electrical machines )
  
                - DC machines in details, principle of operation, internal construction and their applications
                - AC machines in details, principle of operation, internal construction and their applications
                - How can you read the data on the nameplate of the motor
  
  5- section (5) :  ( Designing of Electrical Control circuits )
  
                  - Start/Stop for 3ph I.M 
                  - Start/Stop for 2  3ph I.M ( Latching - Interlocking Concepts )

                  - Star/Delta circuit manually and Automatically in details
                  - Start/Stop from different places concept
                  - Forward/Reverse Concept
                  - Star/Delta & Forward/Reverse control circuit
                  - 3Three 3ph I.M as sequence one after another

                  - Advanced 4 applications 
                  - Solutions of the First assignment
  
  6- section (6) :  ( Electrical sensors and Encoders )
  
                  - what's the difference between sensor and actuator
                  - Limit switches and reed switch in details

                  - wiring of all sensors in the practical life
                  - Proximity sensors ( Inductive & Capacitive ) in details
                  - photoelectric sensors ( through beam - retro reflective - diffused ) in details
                  - Level sensors ( float switch - Optical - Capacitive - Conductive - Tuning fork switch ) in details
                  - Rotary Encoders ( incremental & absolute ) in details

                  - wiring of Encoder in the practical life  
                       
  
  7- section (7) :  ( Methods of starting for 3ph I.M )
  
            - why do we need for the methods of starting !!!
            - How can you calculate the starting current for the motor using the nameplate data

            - DOL direct on line, Star/Delta , Soft starter, VFD variable frequency drive and Auto-transformer
            - Soft Starter device in details
            - VFD in details
            - wiring for the soft starter and VFD in the practical life
  
  8- section (8) :  ( ATS circuits )
  
                 - Basic components for the Automatic Transfer switch circuit
                 - what's the difference between O.T.T and C.T.T circuits

                 - ATS circuit in details for the new Generator
                 - ATS circuit in details for the old Generator
  
  ** Our help in " Power Tech Academy " is always available to you if you get stuck or have a question !!!
    our support is legendary in Udemy

  
  

  --> So don't hesitate and click " Buy Now " button so you can begin on the right path!
                   
  
  
  
  

TAKE THIS COURSE